Ford axle identification.

The first thing you should look for is the Safety Compliance Certification Label. It could be on any door panel, front or back. Look for the axle and note the code under the axle. By the axle ratio, you can tell what rear-end your Ford F150 has. For detailed information about the rear end of your truck, read this full article.Vehicles. Take the route to proven performance with Spicer ® parts and Dana axle components for Ford ®. These genuine service parts are application-engineered specifically for Ford vehicles, and our rigorous standards assure dependability and durability. When it’s time to replace Ford drivetrain or axle components, get the highest-quality ...One crucial piece of information provided by the Ford Axle Code 3J is the gear ratio of the axle. The gear ratio determines the number of turns the driveshaft needs to make for each turn of the wheels. It affects acceleration, towing capacity, and fuel efficiency. Look for the code prefix "39" to identify the specific gear ratio.Ford Front Axle ID. Refer to our Ford axle identification charts to quickly Identify the parts and information you need. Each of our Dana 44 and Dana 60 front axle identification …Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass., Mercury '67-'69: 3.10: 8 1/2 in: NL-Non-Removable Carrier: WER-AA: Ford Pass., Mercury '77-'78: 2.47: 8.75: NL: 28:

One crucial piece of information provided by the Ford Axle Code 3J is the gear ratio of the axle. The gear ratio determines the number of turns the driveshaft needs to make for each turn of the wheels. It affects acceleration, towing capacity, and fuel efficiency. Look for the code prefix "39" to identify the specific gear ratio.

Axle identification. I just bought a 2001 F350 with the 7.3L. I was just wondering if anyone would be able to tell me for sure what axles I have in both the front and the back. Ive heard a bunch of different crap from people about DANA 50, DANA 80s, and the ford 10.25". I figured i could probable figure it out by looking at the vin or crawling ...

The Ford Axle Code L9 refers to a specific axle ratio used in Ford vehicles. In this section, we will explain what the L9 code stands for, its significance, and how it affects the performance of the vehicle. The L9 code typically represents a 3.73 axle ratio. The axle ratio indicates the number of times the driveshaft must rotate for the wheels ...Early Ford Axle Identification. This article will cover Ford axles from 1928-52 passenger cars & pickups. Keep in mind, this is for Ford cars & pickups only. Trucks and other makes such as Lincoln do not apply. Ford Model A Axle Spring Perch Boss = 2.25" Perch Boss Center to Center = 36.5" Kingpin Center - Center = 50.5" Kingpin Diameter …Ford Rear Axle Assembly Identification - Page 02: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WCN-M: Ford Pass '63: 4.11: 8 3/4 in: NL-Damper Type Flange: WCN-P: Ford Pass '63: 3.50: 8 3/4 in: NL-If you are an automotive enthusiast, chances are you have heard of Dana rear axles. These robust and reliable components have been used in various vehicles for decades. However, id...Axle codes for Ford Explorer, Ranger and Bronco II. Axle identification Ford Explorer, Bronco II, Ranger.

4. Axle Code 27 - 3.31 Open Rear Axle. This code designates an open rear axle with a 3.31 axle ratio. It strikes a balance between fuel economy and performance, being commonly found on F150s equipped with smaller engines. 5. Axle Code K2 - 3.55 Electronic Locking Rear Axle w/ Torsen Differential.

Mean Max. 14314 posts · Joined 2007. #8 · May 9, 2009. You'll want one from an Explorer. '95-'01 will get you rear disc brakes, earlier models will have drums. Look on the driver's door of the donor Explorer for the axle code on the VIN sticker. Explorer 8.8 Axle codes. 43 Open 3200 3.08. 41 Open 3200 3.27.

That said, they're not failure prone until you lift the trucks and run big tires. For normal trucks, they still last forever and a day. Awesome thanks. 1987 - 1996 F150 & Larger F-Series Trucks - Rear F350 Axle Tag Identification (help) - Sorry in advance that I dont have a better photo, but I stumbled across a 1990 F350 SRW 5.8L 5-speed today ...1987 - 1996 F150 & Larger F-Series Trucks 1987 - 1996 Ford F-150, F-250, F-350 and larger pickups - including the 1997 heavy-duty F250/F350+ trucks. Sponsored by: ... Ford Rear Axle Assembly Identification - Page 11 - FORDification.com 4.10 = ratio. If it had an 'L' between 4 & 10 it would be limited slip. 10 2 = ring gear diameter. 10.25" ...To help you find the right part, we first need to properly identify the axle you have or need. Not all vehicles are set up the same, even though they may be the same make and model. A Chevy 1/2 ton pick-up may have a Chevy 10 bolt rear axle or a 12 bolt rear axle. Both of these are semi-floating axles. A Chevy 3/4 ton pick-up may have a 14 bolt ...BRONCO M220 REAR AXLE ASSEMBLY 4.70 RATIO W/ELECTRONIC LOCKING DIFFERENTIAL. M4000470B. $2,485.00. or redeem up to 497,000 Points.If it is a Ford '99-'03 SuperDuty pickup with single rear wheels (SRW) and a 7.3L diesel engine, then it has a Ford "Sterling" 10.5" rear axle. The "Sterling" means it was manufactured in the Ford axle plant in the little town of Sterling, Michigan. The only numbers on the axle tag that mean anything to most of us is the "3L73 10 5" at the ...Ford Rear Axle Assembly Identification - Page 07: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. '82-'83: 3.42: 8.5: L: 28-WFC-G: Capri, Mustang, Cougar 82 Fairmont, Zephyr, Granada 82 Lincoln Continental '82 Thunderbird 82: 3.08: 7.5: L: 28-Influence of axle ratios on speed and acceleration. Axle ratios directly impact the speed and acceleration of the Ford F150. A lower axle ratio, such as 2.73, provides higher top speed but slower acceleration. Conversely, a higher axle ratio, such as 4.10, lets you accelerate quickly but reduces the top speed.

None so far have impressed me enough to consider buying (due to the condition of the truck overall, not the engine). There is a 2007 F-350 that just came up for sale here locally and the door sticker has the axle as "4N". This doesn't jive with any of the documentation I've seen for axle decoder. I'm hoping this truck has 4.30's.You should come visit the team at Access Ford of Corpus Christi, located at 3860 I-69 Access Road in Corpus Christi, TX. Our dealership has a wide selection of new Ford models from which to choose, including fan-favorites like the Ford F-150, Ford Bronco, Ford Explorer, Ford Edge, Ford Escape, Ford Mustang, and Ford Ranger.Identifying plants can be a tricky task, especially for those who are new to gardening. With so many different species of plants, it can be difficult to tell them apart. Fortunatel... Differential Models. Ford - Differential Identification Shop by your differential. Please select a rear end that matches your vehicle below. Ford has a wide range of front and rear ends! We carry everything from the 8" IFS front end parts, to the large 10.5" rear end parts for F-Series trucks. We make it easy to verify your exact rear end. Identification: Dana axles are very easy to identify and their numbering system is consistent irregardless of the vehicle they came in. ... In 1977.5 Ford’s new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in ...

Front Axle Identification. To help you find the right part, we first need to properly identify the axle you have or need. Not all vehicles are set up the same, even though they may be the same make and model. ... FORD FRONT AXLES . Find your Ford vehicle in the chart below and click on the illustration for a larger view. Year. Vehicle. …Contact. You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 15. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 15. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L.

Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:This differential ratio, or axle ratio, is the formal way of saying "rear end." It is important information because the ratio is determined by the number of revolutions of the driven wheels (axle) in comparison to engine and transmission revolutions. Ford may manufacture F150s of various differential ratios to meet the needs of consumers.Note: The lengths stated are for a complete axle from brake drum to brake drum. For 64-73 Mustangs subtract 5 inches to get the bare axle housing width. 65-66 Mustang. 57.25 inches. 67-70 Mustang. 59.25 inches. 71-73 Mustang. 61.25 inches. 77-81 Versailles.Ford is a well-known automobile manufacturer featured in Popular Mechanics Magazine.. 8 axle codes? 8 axle codes refers to the identification codes used in vehicles to indicate the type and specifications of the axles. These codes provide information about factors such as gear ratios, payload capacities, and towing capabilities. They are …1966 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 6: 2.80 open differential: F: 2.80 locking differential: 2: 2.83 open differential: B: …The axle code 15 in a Ford Expedition refers to a 3.73 non-limited slip axle ratio. The axle code 15 indicates that the Expedition is equipped with a rear axle ratio of 3.73 and does not have a limited slip differential. This axle ratio is ideal for towing and hauling heavy loads, providing better torque and power for these tasks.Though flying ants and termites look similar, these pests require very different treatments. Learn more with Today's Home Owner’s guide to flying ants vs termites. Expert Advice On...Dana Differential Identification. The Bill of Material (BOM) number is used to identify Dana differentials. Traditional BOM's are six digits long and begin with the number 60 or 61 followed by 1 or 2 digits, such as 605561-1. Later-model BOM's may start off with the first three digits of 200 rather than 60 or 61, for example 200561-1.Ford Rear Axle Assembly Identification - Page 14. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.

F-350 rear axle identify. I bought a rear axle with a broken ring gear for a project truck. In working on my F350 driver I needed to replace a rear caliper and found there was a right and left. I thought (scary things happen) and looked at my project rear axle and it does not have a right or left. The right caliper hangs on the rear and the ...

Received 648 Likes on 543 Posts. Welcome to FTE. SN = Spicer model C4054A 5 Speed Direct Manual Transmission. 67M: 67 = Rockwell-Timken model F106 One Speed Rear Axle / 5.29-1 / 15,000 lb. Rear Axle Capacity // M = Ford 7,000 lb. Capacity Front Axle with Power Steering. Reply Like.

Aug 31, 2022 · This makes them a popular axle for vehicles on the street and at the track. It is important to understand the design, components, identification, and functions before building or rebuilding a Ford 9" rear axle. Below are answers to the most common questions about the Ford 9” differential: How To Identify A Ford 9 Inch Rear End The 12 Bolt Sterling Axle. The Ford Sterling axle has two generations, currently. And are relatively easy to identify if the axle and brakes were kept 100% stock. The Sterling 10.25″ axles have an 8 x 6.5″ lug pattern, came with drum brakes, and were only used in Ford trucks built between 1985 and 1997.In 1977.5 Ford's new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977. The F-250 is a little wider than the F-100 & F-150, for the wider 8 bolt wheel pattern.The first thing you should look for is the Safety Compliance Certification Label. It could be on any door panel, front or back. Look for the axle and note the code under the axle. By the axle ratio, you can tell what rear-end your Ford F150 has. For detailed information about the rear end of your truck, read this full article.The axle tags also provide information on the axle ratio, limited slip differentials, and lubricant requirements. 2005 and newer axles will also have an assigned axle code, but for these years, Ford specific parts lookup is usually based on the truck serial number (Vehicle Identification Number or VIN).Originally Posted by bryyce62. Front axle is a monobeam Dana Super 60. Rear axle is a Ford Sterling full floating beam 10.5". As for the T-case, all I can find is that it's a 2 speed, part time unit. Pages 82 & 83 of the 2013 F-series order guide. Kind of hit it. Front axle is a standard d60 for f250 and 350.The Sterling 10.5 axle is an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI.It was first used in model year 1985 Ford trucks. The axle was developed to replace the Dana 60 and Dana 70.The Sterling 10.5 axle is currently only made as a full floating axle.. 10.5 Sterling axle in 2011 Super Duty (without the electronic locking differential ...Ford only used 3800 pound rated Dana 60 closed knuckle front axles in 1974 and 1975 F-250 Crew Cab 4x4 trucks. Externally, the axle looks very similar to the Dana 44HD axle that was an option on F-250 regular cab models. Ford built a good number of 1974-1975 Crew Cab F-250 4x4s, but most were shipped to Alaska for use during the construction of ...The solid axle in a F-150 is also a "live" axle, because it transmits power to the wheels. A solid axle is comprised of: Axle tubes welded to a differential housing. Differential cover. Axle shafts that run inside the axle tubes. Differential gears that transmit power from the driveshaft to the axleshafts. Wheel bearings in the outer end of the ...

The solid axle in a F-150 is also a "live" axle, because it transmits power to the wheels. A solid axle is comprised of: Axle tubes welded to a differential housing. Differential cover. Axle shafts that run inside the axle tubes. Differential gears that transmit power from the driveshaft to the axleshafts. Wheel bearings in the outer end of the ...Mar 14, 2024 · The image below shows the Safety Label of a Ford Truck. From the arrow, you can see the axle code is H9. As you proceed to the Ford Axle Code chart, you will notice that the table indicates it has a Ford 8.8″ Limited Slip Differential with an Axle Ratio of 3.55. Find the axle code from the Safety Compliance Certification label. But the axle on it is not a banjo. Here is a picture: There are numbers on each corner of the diff cover. Top Left: U S Patent 1 888 618 Bottom Left: U.S. Patent 2 018 188 Bottom Right: 41 Top Right: 18423 and then also the number 5 was stamped at a perpendicular angle to those numbers. On the Axle tube to the right of the pumpkin there are the ...Instagram:https://instagram. 2 ohm wire diagramwhat happened to john hickey from wnep tvculver's beloitsprouts victorville opening date F66 = F600 4x4 gas. E = 361 4V XD FT gas V8. V = Kentucky Truck Plant. 080631 = 1977 numerical series, December 1976 production. F600 4x4 came in 3 GVWR levels--. F650 = 17,200 lbs. F660 = 21,700 lbs. F661 = 24,000 lbs. These are the model numbers that would appear on the warranty plate, and maybe on a build sheet if you find one.Also, I've never properly ID'd my axles, the front axle has the following info on the label: DANA PN: 610740 1 21-AUG-97 3.54 STD. D-4 7 8-B. CUST PN: F7TA-3002-BA. (P) SERIAL NUMBER: 2970806730 BVA Y. K 50. Thanks for any help guys, I'm affraid if I don't get this fixed before flight school starts, I'll never get around to it and won't be able ... free proxy server youtubegasbuddy sturgis mi The axle tags also provide information on the axle ratio, limited slip differentials, and lubricant requirements. 2005 and newer axles will also have an assigned axle code, but for these years, Ford specific parts lookup is usually based on the truck serial number (Vehicle Identification Number or VIN).3J axle code. My understanding is that 3J = 3.55 Electronic Locking. I'm looking at changing the rear and front axle fluid per the owners manual but wasn't sure if I had limited slip. Manual says 5.8 pints of Motorcraft 80W-90 premium rear axle lubricant for the front axle and 6.9 pints of Motorcraft 75W-140 synthetic rear axle lubricant for ... drag racing games unblocked games To determine which one you have, check the number of splines your axle has. If it has 30 splines or less, then it's a Dana 60 axle. If there are 33 or 35 splines, then you have a Dana 70 axle. If you have a 1994-2001 Dodge you may have a Dana 80 axle which also has 35 spline axle shafts. There are three variations of the Dana 60 axle.Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28-The Ford Sterling 10-1/2" Rear Full-Floating Axle was introduced in 1999 along with the new Super Duty F250 and F350. It shares some parts with the similar 10-1/4" Sterling Rear Axle which Ford used from 1985 to 1997 in the F250 and F350. The 10-1/2" Sterling is equipped with disc brakes (with the possible exception of some very early ...